Welcome to Rock Crawlers Of ATL. We hope you enjoy your visit.


You're currently viewing our forum as a guest. This means you are limited to certain areas of the board and there are some features you can't use. If you join our community, you'll be able to access member-only sections, and use many member-only features such as customizing your profile, sending personal messages, and voting in polls. Registration is simple, fast, and completely free.


Join our community!


If you're already a member please log in to your account to access all of our features:

Username:   Password:
Add Reply
Lipo Batt.
Topic Started: Dec 29 2007, 06:35 PM (244 Views)
Superman
Member Avatar
AKA REX
[ *  *  *  *  *  *  *  *  *  * ]
I went to Hobbytown and got a 1320mah 2 cell Li-po, just curious on the power it will put out. I was running the front saddle packs for the front axle from the crawler store a 6 cell 1500 nimh pack. Will the li-po have more power? I was told that I could add an extra cell and get alittle more to the packs like i had, but after the last comp. and my battery got fried I went ahead and got a li-po. Just curious cause i have ordered a charger and it hasn't arrived yet! (:
Offline Profile Quote Post Goto Top
 
CYCLONE
Member Avatar
100% Rock Crawler
[ *  *  *  *  *  *  *  *  *  * ]
I think it should be about the same, even better

I ran a Li-po 2100mah on my Ax10, and went about 4+hrs with no charge

:)
Offline Profile Quote Post Goto Top
 
aaugman
100% Rock Crawler
[ *  *  *  *  *  *  *  *  *  * ]
I'm running a 1250 lipo as well but i'm too scared to run it down because i havn't figured out if my esc is already set to lipo or not. its supposed to cut off at the last 25% of power or the battery can blow up. so i end up charging it after each run...i probably shouldn't do that.

Offline Profile Quote Post Goto Top
 
TheROOSTER
Member Avatar
100% Rock Crawler
[ *  *  *  *  *  *  *  *  *  * ]
It should be about the same. The battery you had was 7.2 volts and a 2 cell Lipo is 7.4. A 3 cell Lipo is 11.1. The only difference you may notice is a little more torque when accelerating.
Offline Profile Quote Post Goto Top
 
CYCLONE
Member Avatar
100% Rock Crawler
[ *  *  *  *  *  *  *  *  *  * ]
I have the Rooster Crawler ESC and Integy 55T brushed in my AX10
I've been running both a 6cell Nimh.... and a 2 cell Li-Po 2100mah

Im thinking of dropping my 3cell (11.1v) Li-Po in.....Has anyone run that setup ?
Will it hurt the ESC/Motor/servo ?

:wtf:
Offline Profile Quote Post Goto Top
 
TLTRyan
Member Avatar
100% Rock Crawler
[ *  *  *  *  *  *  *  *  *  * ]
CYCLONE
Feb 18 2008, 08:45 PM
I have the Rooster Crawler ESC and Integy 55T brushed in my AX10
I've been running both a 6cell Nimh.... and a 2 cell Li-Po 2100mah

Im thinking of dropping my 3cell (11.1v) Li-Po in.....Has anyone run that setup ?
Will it hurt the ESC/Motor/servo ?

:wtf:

I thought the rooster crawler was rated for 8.4v max. :angry:
Offline Profile Quote Post Goto Top
 
TLTRyan
Member Avatar
100% Rock Crawler
[ *  *  *  *  *  *  *  *  *  * ]
I run a 3 cell with a 55t, but im using the Mamba Max and a CC BEC.

Nice to have the extra speed.
Offline Profile Quote Post Goto Top
 
CYCLONE
Member Avatar
100% Rock Crawler
[ *  *  *  *  *  *  *  *  *  * ]
your right, 8.4v.
Seems like someone said it would still do 11.1v

i better not push it, just checking.. :unsure:
Offline Profile Quote Post Goto Top
 
1 user reading this topic (1 Guest and 0 Anonymous)
« Previous Topic · CRAWLER TECH · Next Topic »
Add Reply

Theme by Sith of themeszetaboards.com